Do you drive a forklift at work? Forklifts are often the workhorses of production halls and plants. Yet they also represent one of the greatest dangers in the workplace, as heavy machinery passes through the plants and warehouses.
Under certain conditions, forklifts and other workers working with heavy equipment may be exposed to hazards. These include collisions, rollovers, and takeoffs.
But if the crews follow the right safety rules, they can be more secure than ever.
Here’s everything you need to know about equipment safety with forklifts.
Perform routine equipment inspections during operation. Notify management of any damage or problems, according to the U.S. Department of Labor code. Remember safety first, always.
Always wear a seat belt and personal protective equipment, such as those provided by your employer when operating a forklift.
It is recommended that you wear at least one piece of protective clothing when working with forklifts. As overturning forklifts are one of the most common causes of accidents, drivers must buckle up.
By exceeding the weight capacity of a forklift, an employee can significantly increase the risk of the machine tipping.
Keep the load within the weights and capacities of your forklifts, but keep it at a reasonable distance from the cage tip.
You can check your load capacity in the operating instructions and list it on your machine yourself. According to the manufacturer’s website, the load capacity can be doubled, tripled, quadrupled, or in some cases, even quadrupled.
Remember, forklift safety at work can save lives.
Motorists should use the horn. These warn pedestrians and other forklift drivers to avoid unnecessary collisions. However, the horn should only be used under restricted visibility.
Take corners and bends slowly to minimize the risk of tipping. Apply the parking brakes, lower the fork, and adjust the controls to neutrality during operation.
The best forklift is the one that responds to your needs in the quickest amount of time to help you carry out your construction work quickly and safely.
If a forklift is parked at an angle, employees should continue to attach the machine to the wheel block. A device that is safely stored reduces the risk of unintentional movement when left unattended. If you want to consider operating machinery, always undertake training and use your judgment.
Fuel cylinders that show signs of wear or leakage should not be used or replaced until they have been requalified at the time of requalification. Store the cylinders in a safe rack or cage. Check for wear on the O-ring valves.
A local propane supplier or plant can help determine whether the cylinder storage basket is in a safe place. Safe places count as a warehouse, a storage car park, or a warehouse.
When removing from the bearing, operators should use the correct lifting equipment when placing a propeller cylinder on a forklift. Position propane cylinders in the upper position. Then, position pressure relief valves, and attach O-ring valves at the bottom.
Make sure the pressure relief valves on the propane cylinders are safe and point away from the locator pin. Check that the pressure relief valve is about 180 degrees. Then close the valve and cylinder to prevent possible damage to the cylinder, propeller cylinder, or O-ring valves.
It is also important to note that the propane industry is introducing special procedures to support companies operating propane and propelled equipment. This includes support to local propane suppliers throughout the country.
Propane suppliers can provide additional safety support in a variety of ways.
First, they can help your crew find the most suitable location for the cylinder cages, so they don’t interfere with your workflow.
You can also remove damaged cylinders from service or repair and replace worn valves or O-rings on the cylinders if necessary. Every time you replace a cylinder, check it for signs of failure, such as a defective valve or a worn valve ring.
Some propane suppliers also offer additional safety training for forklift customers. These suppliers work to ensure that employees understand how propellers and cylinders can be safely installed on their forklifts.
If in any doubt, read the instructional manual and ask for help. If these steps still haven’t fixed the problem, then don’t continue with your journey regardless. This could have fatal consequences that you would be responsible for.
Instead, report the truck as needing the attention of a propane supplier-trained mechanic and get a new machine.
Equipment safety is vitally important when it comes to controlling a forklift. You must ensure that you follow all the rules and regulations of the U.S Department of Labor.
Failure to comply can lead to legal proceedings against you. Your company can also choose to fire you for misconduct regulations if they find out.
Be aware of the environment around you and always wear a seatbelt, even if you are going very slowly.
Undertake routine inspections of the vehicle you are driving and ensure that your supervisors inspect it for damage. If something doesn’t feel right, then carry out more checks before continuing.
Only use your horn when necessary to indicate that something is amiss. Using it in the wrong circumstances can cause confusion. It might also be against company policy.
If you are interested in learning more about equipment safety, be sure to check out the rest of our site.